A plasma cutter is a new type of thermal cutting machine for metal fabrication, which uses working gas and plasma arc with high-speed & high-temperature as the heat source to melt the metal locally, and blow away the molten metal with high-speed airflow at the same time to form a narrow plasma cut seams.
This video is about how I went about building my CNC Plasma Cutting Gantry.
Steel Tubing Gantry, Flat bar slat table, water bed, C&CNC controller, Microsoft XP Windows Computer, Parallel and Serial Port Communication, DHC, Arc Voltage Height Control, Hypertherm Plasma Torch. I program it with SheetCam
This video is about how I went about building my CNC Plasma Cutting Gantry. Steel Tubing Gantry, Flat bar slat table, water bed, C&CNC controller, Microsoft XP Windows Computer, Parallel and Serial Port Communication, DHC, Arc Voltage Height Control, Hypertherm Plasma Torch. I program it with SheetCam source
UPDATED DIY VERSION (I made better one): https://www.youtube.com/watch?v=D-22mZZNXHo
I am in the process of building a homemade CNC Plasma table. This table is designed to use a 4ft by 4ft work piece and utilizes LinuxCNC software with HobbyCNC electronics. Plasma cutter is an Everlast Powerplasma 60s with machine torch. This video goes over the frame and computer mounts and motion rails that I am using for the build. The next video will cover electronics! Very fun build! Link to the sliders I used for my build from ebay: https://www.ebay.com/itm/CNC-Router-Plasma-Gantry-Carriage-Rail-Car-NEMA-23-motor-2×2-2×3-or-2×4/123469747929?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
Chapters:
0:00 Introduction
0:41 Parts Overview
2:51 Frame Start
5:19 Slat Holders Installation
6:15 Painting and Hardware
7:15 Final Touches
10:55 Final Overview
UPDATED DIY VERSION (I made better one): https://www.youtube.com/watch?v=D-22mZZNXHo I am in the process of building a homemade CNC Plasma table. This table is designed to use a 4ft by 4ft work piece and utilizes LinuxCNC software with HobbyCNC electronics. Plasma cutter is an Everlast Powerplasma 60s with machine torch. This video goes over the frame and computer mounts and motion
In this episode, Jim Colt, an industry veteran from Hypertherm, talks about cutting diamond plate with plasma. Visit https://www.maverickcnc.com/ for more information on all of our plasma cutting tables.
MaverickCNC plasma cutting tables cut vehicle custom parts, signs, artwork and logos from Diamond plate with Powermax plasma. Using the Powermax plasma with a mechanized torch and Arc Voltage Height Control, Jim walks you through cutting anti-skid plate, diamond plate, traction plate with CNC plasma machines.
Be sure to subscribe to our channel and click the bell icon to get notified when new “Tips and Tricks from Jim Colt” videos are released.
Video description :
Hi, Jim Colt here with MaverickCNC, we have a Hypertherm plasma cutting system on this machine.
Just a little tip, we get questions all the time about cutting diamond plate or tread plate, often it’s aluminum, decorative aluminum tread plate or steel tread plate, it might be used in a truck body and because it has all those little bumps, all those little treads on it, a lot of people ask questions about it. It really depends which way you cut it, there are two choices one is to cut it with the bumps up, one is to cut it with the bumps down.
If you have a machine with no height control or poor height control – cut it with the bumps down because your going to have collusions, your going to have problems with the bumps on it. If you have a machine with a good quality integrated height control, like this MaverickCNC has, put the bumps up and your going to get the best quality.
What you want to do for the thickness rating of it, the nominal thickness of the material, not including the bump is the speed rating and the spec that you should actually set for, right out of the cut charts that are built into the CNC control or in the Hypertherm manual so put the bumps up, cut it like it’s just a piece of eighth inch steel, has an eighth inch nominal thickness and your going to get the best cut quality. It’s kind of fun to watch as the torch height control accurately climbs over every one of those bumps without making contact with the plate.
Very good process and it’s a good way to cut that material where it’s a material that people thought, in the past, they had to cut it with a hand plasma torch or with a shear and today it can be cut on CNC cutting tables.
In this episode, Jim Colt, an industry veteran from Hypertherm, talks about cutting diamond plate with plasma. Visit https://www.maverickcnc.com/ for more information on all of our plasma cutting tables. MaverickCNC plasma cutting tables cut vehicle custom parts, signs, artwork and logos from Diamond plate with Powermax plasma. Using the Powermax plasma with a mechanized torch and Arc Voltage Height Control,
Part 1 of building a CNC Plasma Cutter, making the gantry and the frame. Plans – https://jdsgarage.bigcartel.com/ #CNC #Plasmacutter #DIY For all inquires email us jsaction4[at]gmail.com Air Hockey Saloon by Chris Zabriskie is licensed under a Creative Commons Attribution 4.0 license. https://creativecommons.org/licenses/by/4.0/ Source: http://chriszabriskie.com/vendaface/ Artist: http://chriszabriskie.com/ source
