Category: CNC Plasma Cutter

A plasma cutter is a new type of thermal cutting machine for metal fabrication, which uses working gas and plasma arc with high-speed & high-temperature as the heat source to melt the metal locally, and blow away the molten metal with high-speed airflow at the same time to form a narrow plasma cut seams.

CNC Plasma Cutter

How to Cut Metal Using a CNC Plasma Table – Kevin Caron

Kevin Caron, Artist

November 12, 2022

#FabricationTips #KevinCaronArt

From http://www.kevincaron.com – Finally Kevin Caron takes the file he has been working on and makes some sparks cutting out a metal part on his CNC plasma cutting table ….

After creating the file and preparing it in SheetCam, Kevin Caron is finally ready to cut out his sculpture base using his Dynatorch Super B 4×4 plasma CNC cutting table.

Now it’s time to put the part, which Kevin Caron transferred to a thumb drive, into the computer and program that runs the CNC machine.

Before you open the program in the computer, you have to turn on the CNC plasma table. Once the table is on, the computer lets you know with a little sound.

Next you open the “Dynatorch SuperB CNC” program. You accept the little warning, then allow the machine to go through its warm up routine and the table homes itself. Then you open the file, so Kevin Caron opens the file of the base plate with its four bolt holes.

Before cutting out the base plate, though, Kevin Caron likes to do a dry run of the cut, just to make sure your metal plate is positioned properly on the sheet of metal. To do so, you make sure that your torch height control and the button that turns on the torch are “grayed out.” Then when you click on “Start cycle,” the program – and CNC table – will go through the motions without cutting.

Now Kevin Caron knows that that his sheet of 1/2″ steel is sitting in the right position. He has water in the table to cut down the smoke and dust. He’s got his ground attached and the plasma cutter is on and cranked up, so now it’s time to turn on the table and make some sparks!

He clicks on the two buttons that were grayed out (torch height control and plasma cutter activation). Then he clicks the “Start cycle” button and the table starts cutting the metal. It takes about 2:09 minutes to cut out the bolt holes and the plate itself.

Kevin Caron then uses his permanent lifting magnet and engine hoist to lift the base plate out of the metal and shows the edge. The cut is “as smooth as a baby’s butt,” Kevin Caron declares. He points to a little dross around the edge and says increasing the cutting speed a little might eliminate that.

The bolt holes look perfect.

Kevin Caron is ready to go back to work, so you have time to click on the “notification bell” in the upper righthand corner of the YouTube screen to be the first to know when he uploads a new video, and to visit http://www.kevincaron.com to see more how-to videos.

Well, you might want to stick around for another moment to see Kevin Caron flub his mother’s advice ….

“Inspired sculpture for public & private places.”

Artist Kevin Caron has been sculpting full time since 2006. See – and hear – his amazing metal and large format 3D-printed sculptures, which are found in public and private places coast-to-coast and online at http://www.kevincaron.com.

Follow me for more fun and facts:

Facebook:
https://www.facebook.com/kevincaronstudios

Instagram: http://www.instagram.com/kevincaronart

Twitter: https://twitter.com/kevincaronart

source

#FabricationTips #KevinCaronArt From http://www.kevincaron.com – Finally Kevin Caron takes the file he has been working on and makes some sparks cutting out a metal part on his CNC plasma cutting table …. After creating the file and preparing it in SheetCam, Kevin Caron is finally ready to cut out his sculpture base using his Dynatorch Super B 4×4 plasma CNC

CNC Plasma Cutter

How To Build a CNC Plasma Cutting Table | Part 1 – The Basics

Rusty's Metal Cut Signs & Designs

November 12, 2022

Welcome to part 1 of a video series documenting the build of our new CNC plasma cutting table. In this video, I’ll explain the basics of plasma, applying it to the CNC process and the major components I will use.
Upcoming videos in the series will demonstrate testing the electronics, building the table, setting it up and finally, cutting some items on the table.

Items mentioned in this video, include:
Unimig Razor Cut 45 plasma cutter: https://www.unimig.com.au
4 axis CNC kit including 3Nm NEMA23 stepper motor, stepper motor driver and power supplies
Proma Elektronika’s MyPlasm CNC controller and plasma interface unit: https://www.proma-elektronika.com

If you liked the video, please give it a Thumbs Up. If you would like to subscribe to the channel, please hit the Subscribe button and ring the notifications bell to be notified of upcoming videos.
Thanks again for watching and we’ll see you in the next video.

source

Welcome to part 1 of a video series documenting the build of our new CNC plasma cutting table. In this video, I’ll explain the basics of plasma, applying it to the CNC process and the major components I will use. Upcoming videos in the series will demonstrate testing the electronics, building the table, setting it up and finally, cutting some

CNC Plasma Cutter

The Good, The Bad, The Ugly… Crossfire Pro Plasma CNC Table: 6 Months Later

Christ Centered Ironworks

November 11, 2022

Roy’s recommended plasma cutter…
Amazon Affiliate Links:
Hypertherm Powermax 45: https://amzn.to/3m7mr4P or
Hypertherm Powermax 65: https://amzn.to/37wH8mC

Join this channel to get access to perks:
https://www.youtube.com/channel/UCVZa2bQrCprFEk0kzmarilA/join

————————————————————–
Want more Christ Centered Ironworks?
————————————————————–

Want to SUPPORT what we do here at Christ Centered Ironworks Blacksmith Channel?
Visit my channel: https://www.youtube.com/christcenteredironworks
Stop by my website: http://www.blacksmithpdfs.com
Get some merch: https://teespring.com/stores/christ-centered-ironworks
Shop my Amazon Influencer page for shop tools: https://www.amazon.com/shop/christcenteredironworks
Social: https://www.instagram.com/christcenteredironworks

source

Roy reviews his Langmuir Crossfire Pro after 6 months of use. This plasma cnc table review goes over the pros and cons. Langmuir System is not a sponsor. You can find them at www.langmuirsystems.com/. Roy’s recommended plasma cutter… Amazon Affiliate Links: Hypertherm Powermax 45: https://amzn.to/3m7mr4P or Hypertherm Powermax 65: https://amzn.to/37wH8mC Join this channel to get access to perks: https://www.youtube.com/channel/UCVZa2bQrCprFEk0kzmarilA/join ————————————————————–

CNC Plasma Cutter

4' x 4' Lincoln Electric Torchmate 4400 CNC Plasma Cutter, 2019

Revelation Machinery

November 11, 2022

View similar available machine here: https://hubs.ly/H0-ZNvx0

Cutting Area: 4’x4′
Material Cut: Mild Steel (up to 1 inch, Stainless Steel, and Aluminum)
Machine Footprint: 74″x67″
Approx. Weight: 840lbs

Equipped With:
“Plug and Play” plasma cutting system with high-end SINGLE-SOURCE components
Maximum cutting range is 49″ x 49″
FLEXCUT 80 air plasma power source
ACCUMOVE controller
CAD/CAM software and 20″ touch-screen control. Water cutting table
3-burner gas forge and separate tower with operating software/monitor

source

View similar available machine here: https://hubs.ly/H0-ZNvx0 Cutting Area: 4’x4′ Material Cut: Mild Steel (up to 1 inch, Stainless Steel, and Aluminum) Machine Footprint: 74″x67″ Approx. Weight: 840lbs Equipped With: “Plug and Play” plasma cutting system with high-end SINGLE-SOURCE components Maximum cutting range is 49″ x 49″ FLEXCUT 80 air plasma power source ACCUMOVE controller CAD/CAM software and 20″ touch-screen control.

CNC Plasma Cutter

The new Crossfire PRO CNC plasma table from Langmuir systems

Mike festiva

November 10, 2022

In this video I unbox the Langmuir systems crossfire PRO plasma table. I go over some of the features and software and compare the differences between my original Crossfire and the PRO model.
Here’s an affiliate link to the Crossfire website if you are interested in checking out the tables they have to offer.
http://store.langmuirsystems.com/?aff=16
Don’t forget to use the promo code MIKEFESTIVA this will save you $100 at checkout on a table!

Amazon paid affiliate links below.
**After Running the Titanium Plasma 45 for 3 years it’s held up great! But I feel the Hynade CUT 60 CNC Plasma with blow back pilot arc start offers much better value and is PLUG and PLAY CNC ready***
***Use the Hynade Amazon Promo code 05MIKEWELD at checkout and save 5% on selected Hynade produces.***
Amazon Paid affiliate links below
Hynade CNC Blow Back Digital Air Plasma Cutter, Non-HF Pilot Arc Non-Touch Plasma Cutting Machine, THC Torch Height Control Enabled (CUT60DN) https://amzn.to/3DEzR2m

Digital fractional calipers https://amzn.to/2wendbO

12″ Combination square https://amzn.to/3a0yQBQ

9″ Torpedo level https://amzn.to/3a0RcCH

8″ adjustable T bevel square https://amzn.to/2TZiqUX

Here’s some helpful magnetic welding clamps https://amzn.to/2rjNNOi

T joint two axis Welding Clamp https://amzn.to/2EOyy38

Two axis welding clamp 3″ https://amzn.to/2sX1svn

Small light duty 90 degree corner welding clamp small https://amzn.to/2MolQwk

Hobart shade 5 plasma cutting eye wear https://amzn.to/35UUvJO

Disclaimer: Important Safety Information
Your plasma cutter power supply will expose you to high voltage and high amperage electrical components. It is your responsibility to make sure that all work is done safely and with the power disconnected. If you have any doubts regarding your ability to safely perform this work, you should consult the services of a professional electrician. Mike Festiva will not be held responsible for any injury or death resulting from the incorrect or unsafe execution of this procedure.

source

In this video I unbox the Langmuir systems crossfire PRO plasma table. I go over some of the features and software and compare the differences between my original Crossfire and the PRO model. Here’s an affiliate link to the Crossfire website if you are interested in checking out the tables they have to offer. http://store.langmuirsystems.com/?aff=16 Don’t forget to use the

CNC Plasma Cutter

Do I NEED a CNC Plasma Table? Cost Effective Options

Throttle Stop Garage

November 10, 2022

For Canadians – we can now get parts from SendCutSend.com! For everyone…there is a DISCOUNT CODE!!!

Discount Code:
15TSGCAN

How about subscribing and hitting that like button to make everyone happy.

Please consider supporting the channel through our merchandise.
https://throttle-stop-garage.creator-spring.com

source

We all need to get parts cut from time to time and it seems like every car focused YouTube channel has a CNC Plasma these days. I don’t have the space – so what are my options – that’s the subject of this video. For Canadians – we can now get parts from SendCutSend.com! For everyone…there is a DISCOUNT CODE!!!