It is finally time to give you the first look at the Queenbee Pro CNC router and continue the build. You will get my first impressions of the machine and a general review of the kit from Bulkman 3D as I start the assembly. You will see links to some of the Parts I’ve used down below.

And by the way check out my website https://ohengineering.se/

STEPPERONLINE Stepper Motor Driver 1.0-4.2A 20-50VDC – https://amzn.to/3bYJeND

STEPPERONLINE Switching Power Supply 115V/230V S-350-36 – https://amzn.to/3uCu5br

Arduino Nano – https://amzn.to/3unmehG

Arduino Nano Terminal Adapter Shield (Terminal Adapter 3pcs) – https://amzn.to/3vu0iTb

MUZHI SPDT Micro Switch 12 Pcs – https://amzn.to/3yEDQJn

Nema 23 Stepper Motor 4.2A 3.0Nm (425oz.in) – https://amzn.to/2TfJ8KU

Square Linear Guideway Rail HGH15-1000mm +2Pcs HGH15 – CA Carriage Block – https://amzn.to/3fJDwQA

C-Beam Linear Rail (40mm x 80mm) (Silver, 1000mm) – https://amzn.to/3yLIftO

ABB, AF16-30-10-13, 35 Amps, 100-250V AC/DC Coil, IEC Rated Contactor – https://amzn.to/3fq4QVh

If you like what you see, make sure to subscribe so you don’t miss any future updates and if you have any suggestions you can send me an E-mail at: [email protected] or leave a comment down below.

For more updates on what I’m up to between the the videos you can find me on instagram, just search for @offhoursengineering

source

It is finally time to give you the first look at the Queenbee Pro CNC router and continue the build. You will get my first impressions of the machine and a general review of the kit from Bulkman 3D as I start the assembly. You will see links to some of the Parts I’ve used down below. And by the



In this video i will show you around my homemade diy cnc mill.

I started this project a couple of years ago with the aim to build a cnc milling machine from scrap metal.

The project is far from finished but in this video i show the machine cutting steel with a 12mm carbide insert end mill.

If you enjoy this kind of content could you consider subscribing

source

In this video i will show you around my homemade diy cnc mill. I started this project a couple of years ago with the aim to build a cnc milling machine from scrap metal. The project is far from finished but in this video i show the machine cutting steel with a 12mm carbide insert end mill. If you enjoy



Putting together the Premier Plasma CNC Table. I went with the 4×4 table with the Proma THC and water table. This was a fairly easy install if you take your time and read the instructions!

https://premierplasmacnc.com/

Premier Plasma CNC FT4848 Series 4'x4' CNC Table

source

Putting together the Premier Plasma CNC Table. I went with the 4×4 table with the Proma THC and water table. This was a fairly easy install if you take your time and read the instructions! https://premierplasmacnc.com/ Premier Plasma CNC FT4848 Series 4'x4' CNC Table source



*SUBSCRIBE* More progress on the CNC Plasma Table Build. Today I installed the drain for the water bed. This is my second attempt at getting a drain installed. You can find the fail in an earlier build video. This table is built from a precision plasma gantry kit combined with a candcnc electronics package and a Hypertherm Plasma cutter.

Etsy: https://www.etsy.com/ca/shop/makertable?ref=hdr_shop_menu

Website: http://www.Maker-Table.com

Facebook: https://www.facebook.com/makertable1776/
Instagram: https://www.instagram.com/maker.table/
Snapchat: https://www.snapchat.com/add/maker-table

source

*SUBSCRIBE* More progress on the CNC Plasma Table Build. Today I installed the drain for the water bed. This is my second attempt at getting a drain installed. You can find the fail in an earlier build video. This table is built from a precision plasma gantry kit combined with a candcnc electronics package and a Hypertherm Plasma cutter. Etsy: