Watch as we resurface MDF on our Venture Cabinet Nesting Series CNC router.
Why do we resurface spoilboards?
– Remove top layer of board, allowing for better vacuum hold down
– Ensure the spoilboard is level or square to the machine. This allows you to maintain tight and consistent tolerances in regards to depth cuts
– After cutting a large number of sheets of material, the spoilboard is covered in cut marks, which can effect vacuum hold down. By resurfacing the board, you are removing those cut marks and creating a new spoilboard in the process.
When cutting, we suggest placing a rigid material under your cut piece so your bit can cut slightly through the bottom of your work piece, as well. You will end up with clean top and bottom cuts. After running production for a while, you will end up with a lot of holes, scratches, etc on this material. It’s always a good idea to work on a clean, flat surface. This is when you will want to clean up your spoil board. It is always a good idea to surface your material.
Watch as we resurface this sheet of MDF using our Venture Nesting CNC Machine.
CNC Spoil board Resurfacing Watch as we resurface MDF on our Venture Cabinet Nesting Series CNC router. Why do we resurface spoilboards? – Remove top layer of board, allowing for better vacuum hold down – Ensure the spoilboard is level or square to the machine. This allows you to maintain tight and consistent tolerances in regards to depth cuts –
How to Store CNC Nesting Router? Remember these 7 points!
To improve the production efficiency and service life of CNC nesting router, The maintenance must be done well.
1, The Daily Maintenance of Rack Guide Rail
Because it is easy to get dust on Rack Guide Rail during use, it must be cleaned up after use. Otherwise, the machining accuracy will be affected.
2. Use And Maintenance of Oil Kettle
The oil kettle is used to supply oil to the guide rail. Open the cover and refer to the upper line and the lower line. Don’t add too much.
3. Oil-Water Separator and Oil Mist Generator
At the back of the machine, under the acrylic cover, there are oil-water separator and oil mist device, which will automatically release water when the air pressure exceeds 6: before using the machine, observe whether there is oil in the oil mist device. Its function is to help the cylinder lubricate and prevent the cylinder from getting water and rusting. If not, please add it in time to avoid damaging the cylinder.
3. Oil-Water Separator and Oil Mist Generator
After work, we have to open the cover regularly and manually clean up large pieces of fibers to prevent blockage.
5, Spindle Maintenance 1
When we don’t use it, we should take off the tool handle on the spindle, because the long-term tightening state will affect the internal elasticity of the spindle, which may lead to the damage of the spindle. When using it, it is installed, which is a good protection measure for the spindle. 。
6, spindle maintenance 2
In the process of use, the handle will be covered with dust, which must be cleaned up. In the process of automatic tool change of the spindle, the dust be prevented from entering the spindle.
7. Maintenance of Circuit Box
About a month’s time, use a hair dryer or air gun. In the case of power failure, a small wind blows clean from bottom to top at a time. Regular cleaning can prevent the circuit board from being damaged.
If you want to know more about machine maintenance, please contact us
How to Store CNC Nesting Router? Remember these 7 points! To improve the production efficiency and service life of CNC nesting router, The maintenance must be done well. 1, The Daily Maintenance of Rack Guide Rail Because it is easy to get dust on Rack Guide Rail during use, it must be cleaned up after use. Otherwise, the machining accuracy
New design nesting cnc router machine for panel furniture production,new design dust collector hood,say goodbye to dust during furniture production,for more information,please contact by mail :[email protected]，www.dwdcnc.com
New design nesting cnc router machine for panel furniture production,new design dust collector hood,say goodbye to dust during furniture production,for more information,please contact by mail :[email protected]，www.dwdcnc.com source
