Tag: UNO

Laser Engraving Machine

How to make a laser engraving machine – Part 1: DIY control board – GRBL 1.1 – DIY laser engraver

bakidiy

January 24, 2023



How to make 1500mW laser engraving machine
Part 1: DIY control board – GRBL 1.1 https://youtu.be/MVF9vctQjGY
Part 2: Build linear motion system and connect with the controller board https://youtu.be/mhxFtBWxsXI
Part 3: Frame construction & connecting components https://youtu.be/YgwK2dgmOMI
Part 4: Grbl 1.1 compiling, upload and configuration https://youtu.be/p21e0Q2QLMI
Part 5: Test engrave some images on wood and leather https://youtu.be/EiecXR-9D4c

Safety warning: The laser used in this machine can cause permanent eyesight damage, and probably even blindness. When working with powerful lasers, always wear a pair of laser safety glasses designed to block your laser’s wavelength.
————————————-
Watch all of my videos here: http://youtube.com/bakidiy
————————————-
Please subscribe my channel for latest video.

source

How to make 1500mW laser engraving machine Part 1: DIY control board – GRBL 1.1 https://youtu.be/MVF9vctQjGY Part 2: Build linear motion system and connect with the controller board https://youtu.be/mhxFtBWxsXI Part 3: Frame construction & connecting components https://youtu.be/YgwK2dgmOMI Part 4: Grbl 1.1 compiling, upload and configuration https://youtu.be/p21e0Q2QLMI Part 5: Test engrave some images on wood and leather https://youtu.be/EiecXR-9D4c Safety warning: The

CNC Router

Homemade cnc router

윤우아빠

January 4, 2023



자작합판 베이스로 CNC 머신을 만들어봤습니다
목재는 천천히 크게 무리없이 가공이 되는군요
보드는 아두이노 우노 를 사용했습니다

source

자작합판 베이스로 CNC 머신을 만들어봤습니다 목재는 천천히 크게 무리없이 가공이 되는군요 보드는 아두이노 우노 를 사용했습니다 source

CNC Plasma Cutter

Arduino UNO grbl CNC Plasma Table Setup

DNC

January 3, 2023



How to Flash modified grbl onto arduino.
Using MACH3 post processor to generate g code.
Ending film with plans to build

CNC. Fan Cover;
https://www.thingiverse.com/thing:74964

Recently I updated to grbl 1.1 (finally I figured it out it’s really easy now)
In order for grbl 1.1:
No need to open notepad and change the config file
just verify and upload as done before
CHANGE SETTINGS;
$30=0
$31=0
$32=0
(Pins no longer switch)

DISCLAIMER: I am in no way responsible for your actions. This video is meant to be a DIY type/educational video of how I accomplished the outcome. I am good but not “trained” so there are most defiantly “better” ways to accomplish this, this is just one possibility.

source

How to Flash modified grbl onto arduino. Using MACH3 post processor to generate g code. Ending film with plans to build CNC. Fan Cover; https://www.thingiverse.com/thing:74964 Recently I updated to grbl 1.1 (finally I figured it out it’s really easy now) In order for grbl 1.1: No need to open notepad and change the config file just verify and upload as